Hello All,

New to HSMM-Mesh and looking to buy some equipment.  Just purchased 2 Linksys WRT54GS v 1-3s and hope to have them in hand later this week.

Looking for a gently used  TP-Link 24dBi parabolic dish antenna for my system so if anyone have one for sale or an extra one they dont need plz let me know.  You can reach me at my call-sign at gmail.com.

Also looking for a Mesh elmer.  Since I'm so rural it would probably be best for me to learn via email although I'm not opposed to meeting in person if the distance is right.

Hope to hear from someone soon.  Thanks

73

Jeff

I've installed the urlgrey/hsmm-pi repository from GitHub on two PI zero W's that I have and have been using my little network for a year or so.

My PI's are running Raspbian stretch lite, but I suspect that buster would work fine, too.

I've installed the PI's as headless and ssh in through the USB interface from my home network computers (all Linux or BSD).

Try reflashing with .trx file NOT the .bin file

AE5OJ in El Paso

Has anyone been successful in uploading BBHN firmware

to this version? Any suggestions? I don't want to brick it!

Has anyone been successful in uploading BBHN firmware

to this version? Any suggestions? I don't want to brick it!

Hello,

I just tried doing this with Winlink and was unable to get it to work.  Every time I tried it it said it failed because "the target machine actively refused it.". I tried disabling the firewalls on both laptops and even enabling ports, but to no avail.

Any information would be greatly appreciated!

73's

Hello,

I just tried doing this with Winlink and was unable to get it to work.  Every time I tried it it said it failed because "the target machine actively refused it.". I tried disabling the firewalls on both laptops and even enabling ports, but to no avail.

Any information would be greatly appreciated!

73's

Hello,

I just tried doing this with Winlink and was unable to get it to work.  Every time I tried it it said it failed because "the target machine actively refused it.". I tried disabling the firewalls on both laptops and even enabling ports, but to no avail.

Any information would be greatly appreciated!

73's

Hello,

I just tried doing this with Winlink and was unable to get it to work.  Every time I tried it it said it failed because "the target machine actively refused it.". I tried disabling the firewalls on both laptops and even enabling ports, but to no avail.

Any information would be greatly appreciated!

73's

Hello :

Still looking for someone to help with setup, so far no answer.

Also, would like answer on setup with Ubiquite router?

Please advise.

WD4PLB

I have just setup 2 wrt54gl v1.1 routers using 3.1.0 and am having issues getting node 2 to exchange data with node 1. Using localnode:8080 on node 1, I can "see" node 2 and can use the link to access node 2.  I can also ping the wireless address without problem.  However, when I attempt to use localnode:8080 on node 2 to access node 1, I just get a webpage could not be reached timeout error.  Pinging the addresses from node 2 -> node one doesn't work either.  I have tried multiple computers (win and mac) on each node and the results are the same, so the problem does not seem to be computer related

The localnode:8080 works on both routers for status, login and configuration purposes (with any computer that I try), but traffic is only flowing from node 1 to node 2, and not from node 2 to node 1 (other than what I have describe above).

Both installs are 3.1.0 and were done this weekend with no configuration changes other than the setup for node names.

Any help would be appreciated.  (PS i live in Wyoming, so there is no local ham that even has a clue about mesh networking.)

This link might be of interest to configure the ESP8266 for mesh networks:

https://www.esp8266.com/viewtopic.php?f=11&t=16449

Just getting started and thus far having a great time meshing. I'm located at a remote location to other mesher's and was wondering if anyone would offer tunnel access.

My info AD4TH-0 email ssshoema@gmail.com.

Thanks in advance!!